In a small-signal silicon diode at room temperature (300 K), what is the approximate forward voltage required to reach the 'knee' of the characteristic curve where current begins to increase rapidly?
Explanation
The 'knee' voltage is a fundamental characteristic of a diode, representing the approximate forward voltage at which the diode begins to conduct significant current. For standard silicon diodes, this value is consistently around 0.6 to 0.7 volts.
Other questions
What are the names of the two terminals of a diode?
What condition is known as forward bias in a diode?
What is the name of the equation that relates the current and voltage for a junction diode, given by iD = Is[exp(vD / nVT) - 1]?
What is the primary application of a Zener diode?
A certain junction diode at 300 K has a current of 0.1 mA for a forward voltage of 0.6 V. Assuming the emission coefficient n is 1 and the thermal voltage VT is 0.026 V, what is the saturation current Is?
In the graphical load-line analysis of a simple diode circuit containing a voltage source VSS and a series resistor R, what does the operating point represent?
For a simple Zener diode voltage regulator with a variable supply voltage VSS and a fixed series resistor R, what happens to the load line as VSS increases?
When analyzing a complex circuit containing resistors, sources, and a single Zener diode using the load-line technique, what is the first step?
How is an ideal diode modeled when it is in the 'on' state?
When using the 'assumed states' method for analyzing a circuit with multiple ideal diodes, what must be done if the initial assumptions lead to an inconsistent result (e.g., a diode assumed 'off' has a forward voltage)?
What is the purpose of using a piecewise-linear model for a diode instead of an ideal-diode model?
In a piecewise-linear model of a diode's forward-bias characteristic, what circuit elements are typically used to represent a single straight-line segment?
What is the primary function of a rectifier circuit?
In a half-wave rectifier with a smoothing capacitor, what is the small AC component present in the load voltage called?
A power supply using a half-wave rectifier needs to deliver an average load current of 0.2 A to a load. The AC source has a period of 1/60 seconds. To achieve a peak-to-peak ripple voltage of 1 V, what is the approximate required capacitance?
What is the Peak Inverse Voltage (PIV) across the diode in a half-wave rectifier with a resistive load, where the peak AC input voltage is Vm?
How does a full-wave rectifier improve upon a half-wave rectifier in terms of the required smoothing capacitance for a given ripple voltage?
What is the function of a clipper circuit?
What is the function of a clamp circuit?
In a clipper circuit designed to limit the output voltage between -9 V and +6 V using ideal diodes and batteries, what happens when the input voltage is between -9 V and +6 V?
What is the small-signal equivalent circuit of a forward-biased diode operating at a quiescent point (Q point)?
The dynamic resistance (rd) of a junction diode is given by the formula rd = nVT / IDQ. How does the value of rd change if the Q-point current (IDQ) is increased?
What is the computed dynamic resistance (rd) of a junction diode with an emission coefficient n = 1 at a temperature of 300 K (where VT is 26 mV) for a quiescent current IDQ of 1 mA?
When drawing a small-signal AC equivalent circuit for an amplifier, how are DC voltage sources treated?
What type of material is formed in a semiconductor when impurities create positively charged mobile particles known as holes?
According to the approximate form of the Shockley equation for a forward-biased diode, what increment in forward voltage (ΔvD) is required to increase the current by a factor of 10? Assume VT = 0.026 V and n = 1.
A Zener-diode regulator circuit has a supply voltage of 15 V and a series resistor of 1 kOhm. The Zener diode has a characteristic where the output voltage is found to be 10.0 V. If the supply voltage is increased to 20 V, the output voltage becomes 10.5 V. How much did the regulated output voltage change for a 5 V change in the supply?
What is the analysis procedure for a circuit with ideal diodes that have 2 to the power of n possible combinations of states?
What is the purpose of adding a large smoothing capacitor across the output terminals of a rectifier?
In a diode bridge full-wave rectifier, how many diodes conduct during the positive half-cycle of the AC input?
Why might practical wave-shaping circuits use Zener diodes instead of batteries?
What is the relationship between a diode's dynamic resistance (rd) and its Q-point values?
A power supply is needed to deliver 0.1 A and 15 V (average) to a load using a half-wave rectifier with a 0.7 V diode drop. The ripple voltage should be 0.4 V. What is the required peak AC voltage (Vm) needed from the source?
In a battery-charging circuit using a half-wave rectifier, with a battery voltage of 14 V and a peak AC source of 20 V, when does current flow to charge the battery?
What is the peak inverse voltage (PIV) across the diode in a half-wave rectifier circuit with a smoothing capacitor, where Vm is the peak AC voltage?
What is the key feature of a full-wave rectifier circuit using two diodes and a center-tapped transformer?
In the analysis of ideal diode circuits, if you assume diode D1 is 'on' and D2 is 'off', what conditions must the calculated vD2 and iD1 satisfy for the assumption to be correct?
In a small-signal AC equivalent circuit, coupling capacitors are replaced by short circuits. What does this assume about the signal frequency?
A simple piecewise-linear diode model is often sufficiently accurate. What behavior does this model assume in the reverse-bias and forward-bias regions?
What type of diode would be used in a voltage regulator circuit to provide a nearly constant 5 V output from a variable 10 V to 14 V supply?
A Zener-diode regulator with a load has a supply of 24 V, a series resistor R of 1.2 kOhm, and a load resistor RL of 6 kOhm. What is the Thévenin equivalent voltage (VT) seen by the diode?
For the same Zener-diode regulator with a load as in the previous question (supply 24 V, R = 1.2 kOhm, RL = 6 kOhm), what is the Thévenin equivalent resistance (RT) seen by the diode?
In a simple half-wave rectifier with a resistive load and a sinusoidal input, what portion of the AC input appears across the load?
A certain Zener diode has a piecewise-linear model where the breakdown region is represented by a 12 Ohm resistor in series with a -6 V source. What does this indicate about the diode's characteristic curve?
What is the fluid-flow analogy for a diode described in the text?
According to the rule of thumb mentioned in Section 9.1, how does the reverse current of a small-signal silicon diode change with temperature?
In a circuit with a 10 V source (VSS), a 10 kOhm resistor (R), and a diode, you are performing a load-line analysis. An intercept of the load line falls off the page. The other intercept is on the iD axis at 1 mA. What is a good second point to select to draw the load line?
For a small-signal AC analysis of the voltage-controlled attenuator circuit, why is the DC control voltage source VC treated as a short circuit?
In a simple clamp circuit that adds a DC component to an AC waveform, what is the role of the large capacitor?